BMW E39 Betriebsanleitung PDF herunterladen (Seite 7)

3.4 Outside lap belt mounting points – E36 Sedan

 Unbolt the seat from the floor mounts. Move the seat

all the way back and remove the front floor mounting

nuts using a 16mm socket. Move the seat all the way

forward and remove the rear mounting bolts.

 DO NOT REMOVE

THE SEAT. Tip the

seat in toward the

front of the car to

expose the BMW

anchor bolt at the

rear side of the

seat-mount bracket.

 Use a razor blade to

trim back the plastic

as shown in the

picture above to

allow space for the SCHROTH Lap Belt Tail Strap.

 Using a T50 Torx socket remove the bolt that holds

the factory lap belt in place.

 Place the SCHROTH mounting bracket directly

beneath the bolt head and reinstall the BMW factory

anchor bolt. Torque to 30 ft.lbs.

 Reposition the seat over its mounting point and

remount the two front retaining nuts and two rear

retaining bolts.

4 Installation of the tail strap connectors

4.1 Tail strap connectors- Left (Drivers Side) Belt

All E36 models

 No installation is required. Simply plug the male ends

of the SCHROTH harness tail strap into the left most

rear seat and the center mounted rear seat BMW

factory female receptacles.

4.2 Tail strap connectors- Right (Passenger Side) Belt

All E36 models

 Remove rear seat cushion by lifting up firmly on the

front edge of the cushion about 8” in from either side.

 Using a 16mm hex

socket, remove the

anchor bolt holding the

rear passenger side lap

belt.

 Using two pair of pliers,

carefully bend the

SCHROTH bracket so

that it fits as shown in the

picture to the right.

 Reinstall the BMW factory

anchor bolt placing the SCHROTH bracket directly

under the bold head and positioned as shown in the

picture above.

 Reinstall the rear seat cushion being sure that the

SCHROTH tail strap connector is positioned above

the top of the seat cushion.

4.3 Tail strap connectors – Left & Right Belts

All E39 models

 No installation is required for the inboard mounting

points of the tail straps. Simply plug the male ends of

each SCHROTH inboard tail strap to their respective

BMW factory female receptacles in the center of the

rear seat.

 Outer most mounting points require installation of a

SCHROTH Tail Strap Connector. Lift out the rear seat

cushion by lifting up firmly on the front edge of the

cushion 8” in from either side and in the middle.

 Locate and remove (16mm socket) the BMW lap belt

anchor bolts at the outside corners just under the rear

seatback side bolsters. 16mm socket.

 Bend and mount the

SCHROTH tail strap

connector as shown in the

picture to the right.

 Replace the rear seat

bottom cushion being sure

that it is “snapped” in place

at the three front edge

attachment points. The

SCHROTH tail strap

connector should stick out

slightly between the bottom and top cushions.

4.4 Tail strap connectors – Left & Right Belts

All E46 models

 No installation is required for the inboard mounting

points of the tail straps. Simply plug the male ends of

each SCHROTH inboard tail strap to their respective

BMW factory female receptacles in the center of the

rear seat.

 Outer most mounting points require installation of a

SCHROTH Tail Strap Connector. Lift out the rear seat

cushion by lifting up firmly on the front edge of the

cushion about 8” in from either side and in the middle.

 Locate the BMW lap belt anchor bolts at the outside

corners just under the bottom edge of the rear

seatback side bolsters. On some cars it is possible to

“lift up” the lower outside corner of the side bolster to

gain access to the BMW anchor bolt. In other cars it

may be necessary to remove the rear seat back side

bolsters. Please see instructions on page 12

 Remove the bolt using a T50 Torx head socket.

 Mount the tail strap

connector as shown

in the picture to the

right. With the bolt

slightly loose, gently

pull up on the

SCHROTH webbing

allowing the

mounting bracket to

bend slightly so that it is angled in the direction that

the belt will be pulling and will pass easily between the

two seat cushions.

 Replace the rear seat bottom cushion being sure that

it is “snapped” in place at the three front edge

attachment points. The SCHROTH tail strap

connector should stick out slightly between the bottom

and top cushions.

5 Flexible range of the seat belt mounting brackets

Repeated bending could weaken the bracket and cause it

to fail when loaded in an accident.

Never bend the bracket back and forth several times.

Any pivoting brackets of the stock 3-point belts must not

be limited in their range of motion.

1 2 3 4 5 6 7 8 9 10 11 12 13

Kommentare zu diesen Handbüchern

Keine Kommentare

BMW E39 Betriebsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kfz-Elektronik BMW E39