BMW E39 Betriebsanleitung PDF herunterladen (Seite 6)

THIS SCHROTH BMW RALLYE 4

HARNESSBELT IS

ONLY DESIGNED

FOR THE DESIGNATED BMW MODEL

AS SEWN INTO THE LABEL ON THE

HARNESSBELT TAILSTRAP. USE IN

ANY OTHER BMW MODEL OR IN ANY

OTHER AUTO OF A DIFFERENT

MANUFACTURER COULD RESULT IN

THE FAILURE OF THE HARNESS

SYSTEM AND SERIOUS INJURY.

Never drill or tap or make a new attachment point in

the body or chassis in order to mount a SCHROTH

Quick Fit harness at that location. Such attachment

points are inadequate, may be improperly located

and can seriously impair the function and

effectiveness of the system.

Please compare the mounting locations on your car with the

illustrations on pages 7 and verify the “Model Tag” as pictured

above (sewn into the tail strap) matches the model of your

vehicle.

Original equipment belts with swivel attachments must never

be bent, modified, impeded or restricted in their range of

motion.

2 Anchorage bolts & SCHROTH Rallye Bolt on bracket

Where additional SCHROTH connecting tails are to be

installed (referenced by the Green Boxes on the diagrams on

page 7), the SCHROTH connector will be bolted to the a

factory mounting point along with the factory belt using the

factory provided bolts. You should be able to tighten each bolt

a minimum of nine (9) full 360 degree turns. Tighten all

anchorage bolts to a torque of 30 ft.lbs. (40 Nm)

3 Installation of the lap belt connectors

3.1 Outside lap belt mounting points – E36/E46 Coupes

The front outboard lap belt mounting points are located at the

front of the metal rail that holds the bottom of the factory

seatbelt.

 Pop off the black plastic cap to expose the retaining

bolt.

 Using a T50 Torx head socket, back out the bolt.

Place the SCHROTH connector just under the bolt

head and reinstall the bolt.

 Before tightening the bolt, align the SCHROTH

connector so that the webbing is pulling in the same

direction that the belt will pass over your lap when

connected. Torque the bolt to 30 ft.lbs.

 If desired, trim the plastic cover around the

SCHROTH bracket and clip it back over the bolt. A

razor blade or wire cutters work well for this task.

3.2 Outside lap belt mounting points – E39 Sedan

 Adjust the electric seat to the

forward and raised position

giving access to the seat belt

mounting bolt.

 Locate the mounting bolt on

the outer most rear section of

the base of each front seat.

The retaining bolt (indicated

in blue) faces inward.

Remove this bolt using a T50

Torx head socket.

 Feed the SCHROTH lap belt

connector down from the top

between the side of the seat

and the factory belt. (base of

the factory belt is indicated in

red)

 Replace the bolt placing the

SCHROTH bolt-in connector

(pictured in green) immediately behind the bolt head

and the stock bracket (red) behind the SCHROTH

bracket. Torque the bolt to 30 ft.lbs.

3.3 Outside lap belt mounting points – E46 Sedan

 Locate the front outboard lap belt anchor bolt on the

rear outside corners of each seat as pictured above.

Remove this bolt using a 16mm hex head socket.

 Using a razor blade or wire cutters, trim off the small

piece of plastic outlined by the white marks (with the

red “X”).

 Remount the anchor bolt with the SCHROTH bracket

resting immediately under the bolt head and the

factory bracket in its original position. Position the

SCHROTH bracket so that the webbing is following

the desired path once the lap belt is connected.

 Torque the bolt to 30 ft.lbs.

1 2 3 4 5 6 7 8 9 10 11 12 13

Kommentare zu diesen Handbüchern

Keine Kommentare

BMW E39 Betriebsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kfz-Elektronik BMW E39