Please initial and route to the following for information before filing X Service Manager X Warranty X Service Technicians - Initial
10 E46 Sedan with Carrier Rack 1. If the left rear of the trunk is as shown, then a component carrier rack is already installed and the follow
11 8. Locate pins 7 & 8 (2) and carefully remove them from the terminal housing (1). 9. Bend the wires for pin 7 & 8 back away from the
12 14. Connect the 54-pin connector (2) and white FAKRA connector (1) to the ULF Control Module (F) after the bracket is installed. 15. Reinstall
13 6. Attach the two clip nuts (1 & 2), P/N 61 13 1 372 033, to the ULF Control Module as shown. 7. For E46 vehicles produced prior to 8/02
14 11. Bend the wires for pin 7 & 8 back away from the connector 12. Wrap each terminal separately with electrical tape and tape them to the w
15 C. Installation of Voice Input Jumper 1. If a Voice Input Jumper Plug is not installed then a Jumper Plug, P/N 84 11 0 018 038, must be obta
16 Coding ULF Control Module to Vehicle After installing the ULF Kit, the vehicle should be re-coded with DIS/GT1 SW 33 or higher, using the “Retro
17 F. Troubleshooting: Situation Correction No audio output through vehicle speakers Check SES module jumper plug Radio does not mute after placi
18 G. Pairing Procedure: The pairing procedure that must be initiated through the phone will differ corresponding to the different menu configurat
19 4. If the phone identifies/finds a device select it and follow the indicated steps to complete the pairing process. 5. Once the phone is succe
2 PARTS INFORMATION: Description Qty BMW Part Number ULF Control Module 1 84 21 6 934 552 Voice Input System Jumper Plug 1 84 11 0 018 038 U
20 COMPONENT LOCATION: SPORT WAGON SEDAN A - Eject Box C/E - Microphone D - BluetoothTM Antenna F - ULF Control Module
21 SpeakerTel +Tel -Telephone MuteTelephone OnX100152113Cradle Key +Cradle OnX4545X4545BluetoothAntennaI/K Busto other modulesfrom terminal 30 from
22 SpeakerTel +Tel -Telephone MuteTelephone OnX100152113Cradle Key +Cradle OnX4545X4545BluetoothAntennaI/K Busto other modulesfrom terminal 30 from
3 3. Remove the center console storage tray (2), refer to RA 51 16 200. The center console will need to be removed in order to install the pairin
4 8. In order to install the Pairing Button, P/N 84 13 0 302 715, an opening must be cut into the rear of the center console. The area to be cu
5 17. Carefully reinstall the center console. 18. Reinstall the top panel (1) and reinstall the two Phillips head screws (3) making certain that
6 23. Insert the Pairing Button, P/N 84 13 0 302 715, into the cutout and reinstall the cupholders and coin tray. B. ULF Control Module Install
7 E46 Touring 1. Attach the ULF Control Module (F) to the mounting bracket (G), P/N 84 13 6 924 698; use three M5 hex nuts (J), P/N 61 21 1 371
8 4. Prior to connecting the black 54-pin connector to the ULF Control Module pins 7 & 8 will need to be removed from the connector and tied
9 11. Insert the ULF Control Module and bracket (1) into the opening in the inner area of the rear quarter panel, and place the bracket against th
Kommentare zu diesen Handbüchern