BMW Z3 ROADSTER 2.3 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Autos BMW Z3 ROADSTER 2.3 herunter. Power Programmer Instructions Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
99 thru 00 models - Please ensure that you have previously had the "00E-A01 Fault Readiness/O2 Readiness Codes Not Set" emissions recall
update performed by your dealer, if applicable. See Appendix B for a list of the BMW models affected by this recall. Failure to have the recall
update performed prior to using the Power Programmer may cause a “Software Unknown” failure (code 147).
M3 (with SMG transmission) 01 on - Disconnect fuse #33,56 and 61 in the glove box fuse panel prior to using the Power Programmer.
528i and 540i 99 on - Disconnect fuses #17 and #31 in the glove box fuse panel prior to using the Power Programmer.
740i 99 on - Disconnect fuse #17 in the engine compartment fuse panel prior to using the Power Programmer.
PROCEDURE:
1. Locate the rectangular 16-pin OBD-II port in the interior of your BMW. It will generally be found in the driver’s under-dash area, or in the
forward end of the passenger side of the transmission tunnel. The port is protected by a flip-open plastic cover with the word “OBD” on it.
In some cases there is a second removable trim cover over the actual plug assembly. Remove the trim cover if necessary and open the
flip-top cover to gain access to the diagnostic port.
NOTE: The direction in which the LEDs on the end of the Power Programmer will point when inserted into the OBD-II port. You
will need to see these LEDs for guidance from outside the vehicle. In many cases, a mirror will be required to allow you to see the
LEDs from outside the vehicle.
2. Lower the driver and passenger windows, ensuring that you have the ability to reach the OBD-II port.
3. Make sure that the ignition is off and the key is temporarily removed.
4. To ensure a constant voltage for proper operation of the Power Programmer, attach a high-quality battery charger to the vehicle, at
the battery, observing all safety precautions such as the wearing of safety goggles.
5. Turn the charger on at a minimum of the 10 amp setting (20 amp setting if your vehicle is equipped with Daytime Running
Lights–DRLs) and ensure that charging is occurring. Wait a minimum of 20 minutes for the vehicle battery to charge with ample
reserve power.
CAUTION: It is imperative to follow all of the instructions completely and correctly or you may damage your BMW’s
Engine Control Unit (ECU).
BAVARIAN AUTOSPORT
Power Programmer Instructions
Call Toll Free: 1.800.535.2002
275 Constitution Avenue, Portsmouth, NH 03801 • 603.427.2002 • Fax 800.507.2002 • www.bavauto.com
Page 1/4 1.04 INS255
Various
OBD-II
equipped
BMWs
PART NUMBER:
BAVPP4
IMPORTANT NOTES:
Do not even think about beginning this procedure without reading all of these
instructions first.
The Power Programmer can only function on a stock ECU. If your BMW has a
performance programmed ECU, the Power Programmer will not work.
NOTE: Before obtaining any service on your BMW, you should restore the stock settings on your ECU. If your dealer/service
tech restores the settings to stock (which they often do during service upgrades) the Power Programmer will no longer work
on your BMW.
NOTE: The Power Programmer is designed to work only on BMWs that are US or Canadian spec; it will not work on BMWs
built for Europe, Asia, etc.
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - Power Programmer Instructions

99 thru 00 models - Please ensure that you have previously had the "00E-A01 Fault Readiness/O2 Readiness Codes Not Set" emissions recallupda

Seite 2 - 1.800.535.2002

NOTE: The importance of proper battery voltage cannot be emphasized enough. Failure to maintain proper battery voltage throughout the procedure may re

Seite 3

Should the Power Programmer encounter any exceptions or difficulties, the red LED will flash out a 3 digit code at a pace of one flashevery half-secon

Seite 4

BAVARIAN AUTOSPORTPower Programmer Instructions - Appendix BVoluntary Emissions Recall 00E-A01 Fault Access / O2 Readiness CodesPART NUMBERSBAVPP4In a

Kommentare zu diesen Handbüchern

Keine Kommentare